- Introduction
- Maintenance
- Preparation
- Service specifications
- Diagnostics
- 2JZ-GE Engine
- 2JZ-GTE Engine
- 2JZ-GTE Turbocharging
- 2JZ-GE Emission control
- 2JZ-GTE Emission control
- 2JZ-GE SFI
- 2JZ-GTE SFI
- Cooling
- Lubrication
- Ignition system 2JZ-GE
- Ignition system 2JZ-GTE
- Starting system
- Charging system
- Clutch
- W58 manual transmission
- V160 manual transmission
- A340E 2JZ-GE automatic transmission
- A340E 2JZ-GTE automatic transmission
- Propeller shaft
- Suspension and axle
- Brake system
- Steering
- Supplemental restraint system
- Body electrical system
- Body
- Air conditioning system
SST (Special service tools)
 | 09201-10000 | Valve Guide Bushing Remover & Replacer Set | |
 | 09201-01060 | Valve Guide Bushing Remover & Replacer 6 | |
 | 09202-70020 | Valve Spring Compressor | |
 | (09202-00010) | Attachment | |
 | 09213-70010 | Crankshaft Pulley Holding Tool | |
 | 09222-30010 | Connecting Rod Bushing Remover & Replacer | |
 | 09223-15030 | Oil Seal & Bearing Replacer | Crankshaft rear oil seal |
 | 09248-55040 | Valve Clearance Adjust Tool Set | |
 | (09248-05410) | Valve Lifter Press | |
 | (09248-05420) | Valve Lifter Stopper | |
 | 09301-00110 | Clutch Guide Tool | 2JZ-GE M/T |
 | 09316-60011 | Transmission & Transfer Bearing Replacer | |
 | (09316-00011) | Replacer Pipe | Crankshaft front oil seal Camshaft oil seal |
 | (09316-00051) | Replacer “D” | Camshaft oil seal |
 | 09330-00021 | Companion Flange Holding Tool | Crankshaft pulley |
 | 09816-30010 | Oil Pressure Switch Socket | Knock sensor Oil pressure switch |
 | 09843-18020 | Diagnosis Check Wire | |
 | 09950-50010 | Puller C Set | |
 | (09951-05010) | Hanger 150 | Crankshaft pulley Crankshaft timing pulley |
 | (09952-05010) | Slide Arm | Crankshaft pulley Crankshaft timing pulley |
 | (09953-05010) | Center Bolt 100 | Crankshaft pulley Crankshaft timing pulley |
 | (09953-05020) | Center Bolt 150 | Crankshaft pulley Crankshaft timing pulley |
 | (09954-05010) | Claw No.1 | Crankshaft timing pulley |
 | (09954-05030) | Claw No.3 | Camshaft pulley |
 | 09950-70010 | Handle Set | |
 | (09951-07100) | Handle 100 | Crankshaft rear oil seal Valve guide bushing |
 | 09960-10010 | Variable Pin Wrench Set | |
 | (09962-01000) | Variable Pin Wrench Arm Assy | Camshaft timing pulley |
 | (09963-01000) | Pin 10 | Camshaft timing pulley |
Recommended tools
 | 09040-00010 | Hexagon Wrench Set | |
 | 09043-50100 | Bi–hexagon Wrench 10 mm | Cylinder head bolt |
 | 09044-00020 | Torx Socket E10 | A/C compressor stud bolt |
 | 09090-04020 | Engine Sling Device | For suspending engine |
 | 09200-00010 | Engine Adjust Kit | |
 | 09258-00030 | Hose Plug Set |
Equipment
| OBDII scan tool | Engine speed |
| Caliper gauge | |
| CO/HC meter | |
| Compression gauge | |
| Connecting rod aligner | |
| Cylinder gauge | |
| Dial indicator | |
| Dye penetrant | |
| Engine tune-up tester | |
| Heater | |
| Micrometer | |
| Mirror | |
| Magnetic finger | |
| Piston ring compressor | |
| Piston ring expander | |
| Plastigage | |
| Precision straight edge | |
| Spring tester | Valve spring |
| Steel square | Valve spring |
| Thermometer | |
| Torque wrench | |
| Valve seat cutter | |
| Vernier calipers | |
| V-block |
SSM (Special Service Materials)
| 08826-00080 | Seal Packing Black or equivalent (FIPG) | No.1 camshaft bearing cap Cylinder head Rear oil seal retainer |
| 08833-00070 | Adhesive 1324, THREE BOND 1324 or equivalent | Drive plate bolt (A/T) Union for oil cooler hose (2JZ-GTE) |
| 08833-00080 | Adhesive 1344 THREE BOND 1344 LOCTITE 242 or equivalent | Idler pulley pivot bolt Oil pressure switch |
This guide is based on the book edition Toyota (RM502U, 1997)
